Article | EAN | NRF (NRF) | NOBB NOBB |
72.380.337102 | 7072380371028 | 5648884 | 60600391 |
Product information
Waterguard+ Wireless Single 1/2 is an advanced leak protection system designed to monitor and automatically shut off the water supply in homes, holiday homes, apartments and commercial buildings in the event of water leaks, low temperatures that can lead to ice formation and pipe bursts, and high humidity levels. The system is approved by Sintef under approval number TG20834 and complies with Norwegian building regulations, including TEK10 and TEK17. All electrical components in the system are tested and certified according to CE requirements, and comply with REACH and RoHS regulations.
System Overview
The product package consists of the central unit Linkbox+ WiFi, a 1/2" DN15 valve and a sensor tape that detects water leaks, as well as accessories for its installation.
For an extended detection range, the WaterSensor+ wireless water sensor is often installed in combination with the product package. Please refer to FM - WaterSensor+ [Item No.: 72.380.337306 - NOBB: 5648875] – Waterguard Customer Support for information on this product.
Products in bundles
Product Name | Number | Description | Article | EAN / GTIN | NOBB |
Abra Linkbox+ WiFi (A) | 1 st. | The central unit that handles signals from sensors and controls the ball valves. | 72.380.337112 | 7072380371127 | 5648933 |
230V -> 24V 1.0A nätadapter (B) | 1 st. |
24V DC power adapter for Linkbox+ WiFi and Linkbox+ 4G. |
72.380.337315 | 7072380373152 | 5648925 |
Waterguard+ Ball Vavle DN15 1/2" (D) | 1 st. | Ball valve is installed on the water pipe to control the flow of water. | 72.380.337303 | 7072380373039 | 5648911 |
Waterguard+ 1/2" and 3/4" valve actuators (C) | 1 st. | Actuator to control the ball valve based on feedback from sensors. | 72.380.337305 | 7072380373053 | 5648876 |
Waterguard+ sensortejp med 3,5 mm uttag (E) | 1 st. | Wired water sensor detects the presence of water. | 72.380.337307 | 7072380373077 | 5648877 |
Cat.6 Kabel - 2xRJ45 - 0,6 m (F) |
1 st. |
Network cable for connection between the Linkbox+ and the valve actuator.
|
72.380.337324 | 7072380373244 | 5648887 |
(G) Indicates network cable connected to Linkbox+ (not included in product package). Water guard cat. 6 cables (0.6 m or 2 m) can be used, or standard Cat network cable. 5 or later.
For a complete overview of the product packages and products belonging to Waterguard+, see the article Overview of Waterguard+ product packages and part numbers (https://support.waterguard.no/hc/articles/14813969010845).
Installation instructions
Detailed instructions on how to install the product correctly and safely can be found from Waterguard Customer Support under the Installation and User Manual – Waterguard Customer Support (https://support.waterguard.no/hc/categories/13644910475549) section.
General guidelines:
- Waterguard+ is suitable for use in residential, holiday homes, apartments and commercial buildings, both in terms of hot and cold water supply.
- The system must only be installed in a dry and frost-free environment.
- The system is intended to detect water leaks and limit the extent of damage. There will always be some water spillage before the sensors react and the water supply is turned off.
- The valves must be installed by a licensed plumber in accordance with the Constitution. Installation wizard. This is to ensure that the system is working properly, as well as a valid insurance in the event of any water damage.
- In the event of a power failure, the ball valves will maintain the position they had at the front (open or closed).
- The water in the pipeline system must comply with the European Drinking Water Directive.
- The system may only be used in good condition and in accordance with the requirements of the system. Installation and use instructions in this manual.
- The installer must always ensure that the ball valve is installed before connecting power.
For detailed solution descriptions, see the Installation Solutions (https://support.waterguard.no/hc/categories/13644911508893) section.
For the relevant product package with a valve assembly, the following items are applicable:
Description of the solution |
Chosen solution (CHECK THE TYPE OF INSTALLATION) |
Waterguard+ installed on the main intake (cold water) https://support.waterguard.no/hc/articles/4755821964189 |
|
Waterguard+ installed in the kitchen https://support.waterguard.no/hc/articles/4754926847773 |
|
Waterguard+ installed in bathroom and washroom https://support.waterguard.no/hc/articles/13626381528733 |
Instructions
Guidance for normal use of the product, including start-up, operation, and shutdown, see Section 11. Use and maintenance (https://support.waterguard.no/hc/articles/5361731179805) and 12. Locations, Alerts and Signals (https://support.waterguard.no/hc/articles/10029552866717) on the Waterguard website.
The product is intended to last for the lifetime of the building, subject to normal use, maintenance and wear and tear.
Maintenance Procedures
The Waterguard+ system requires minimal maintenance during normal use, in addition to keeping the sensors clean (free of dust and dirt).
However, it is important that the system is function-tested at least 2 times a year to be sure that the system works as intended. Follow the instructions in Article 10. Functional test (https://support.waterguard.no/hc/articles/4629650381597) in the Waterguard+ installation and user manual.
Please note that if the system is installed in public or publicly accessible areas, inspections must be carried out in accordance with applicable regulatory requirements. Although cleaning is not necessary for its functionality, it can be carried out for aesthetic reasons. Clean with common household cleaners, but avoid harsh chemicals containing oil and alcohol, as these can discolor the plastic components.
Safety Instructions
The Waterguard+ is designed with safety in mind and uses a 24V DC power supply. Despite the low voltage, we ask you to be aware of the dangers of electrical products and follow the instructions below.
- The system must only be installed in a dry and frost-free environment.
- The valve and valve components must not be dismantled when the water pipes are pressurized. The water supply must therefore be turned off and drained out of the piping system before installation.
- Visibly damaged cables or equipment should be replaced to prevent short circuits or reduced functionality.
- The central unit with associated power adapters, cables and valve actuators is intended for indoor and dry use only.
- Connection points must not be sprayed directly or indirectly with water or other liquids during use or cleaning.
- The installer must always ensure that the ball valve is installed before connecting power. When connecting power when the valve is not fitted, there is a significant risk of finger injury or damage to the valve as a result of foreign elements in the valve opening.
Troubleshooting Guide
If the valve does not close/open:
- Make sure that the Cat.6 cable is properly connected in both the valve actuator and the Linkbox+ (blue RJ45 connector).
- Make sure that the Linkbox+ is connected to the mains
If the system does not turn off when the sensor tape is wetted:
- Check that the sensor tape is properly connected to the Linkbox+ (jack connector)
- Check that there is no damage or breakage to the sensor tape.
If the system alarms when the sensor tape is moistened but the water remains open, refer to the "simple valve test" section of Section 10. Functional testing (https://support.waterguard.no/hc/articles/4629650381597).
If an extension piece or splitter is used to extend the sensor tape, and some of the sensor losses do not trigger a water alarm in the functional test; Check that the tape is properly connected at the joints. If necessary, replace the tape to clarify whether it is the joint piece or the tape that is the problem.
If the valve does not open after the function test, there is most likely still moisture on the sensor tape. Wipe the sensor tape well and repeat the attempts to open the valve.
Spare parts and accessories
Spare parts
Please refer to the list at the top of the document for a complete overview of the products in the package. These products can be ordered individually at www.waterguard.no and from distributors of Waterguard.
Accessory
For accessories for the Waterguard+ system that can be used to increase the coverage area for water detection or to connect multiple valves, please refer to the Waterguard+ product package overview and part number (https://support.waterguard.no/hc/no/articles/14813969010845-Oversikt-over-Waterguard-produktpakker-og-artikkelnumre)
Legal and regulatory requirements
Generally
The purpose of the system is to detect water leaks and limit the extent of the damage. There will always be some water spillage before the sensors react and the water supply is turned off.
Declaration of Conformity: CE marking and sale within the EU/EEA
Declaration of Conformity for Linkbox+ 4G / WiFi
https://erp.felltech.no/document/share/67/ee3187f0-93c1-433e-a6dd-6cf39b9e65d1
Declaration of Conformity for Linkbox+ 4G / WiFi Power Adapter
https://erp.felltech.no/document/share/68/fd898c5a-7d15-4211-8709-4ba61cea8370
Declaration of Conformity for Ball Valve Actuators
https://erp.felltech.no/document/share/69/5ae05ef1-52ff-4b3b-b39d-f04b5fdf9572
Other:
Waterguard ball valves are tested to meet the requirements for reliable function and service life, as well as hygienic properties for safe use in contact with drinking water.
The valves are certified according to KTW and W270 and certified according to UBA System 1+.
Approval
Waterguard+ is type-approved by Sintef and registered according to TG 20834 Waterguard+ leak arrester (https://www.sintefcertification.no/Product/Download/11188). The system has been tested together with leak detection sensors and valves for water shut-off and found to meet current requirements for function, service life and hygienic properties.
Contact
Distributor
Provider: Waterguard Intl. AS
Organisation number: NO 812 750 062 MVA
Post address: Bragernes Torg 2A, 3017 Drammen, Norge
Phone: +47 23 11 56 60
E-mail: post@waterguard.no
Internet address: www.waterguard.no
Support
See Waterguard's customer support (https://support.waterguard.no) or contact us by phone +47 23 11 56 60.
Guaranteed
Waterguard+ and its accessories are free from material defects and are designed in accordance with the consumer protection laws and regulations of the country in which the product is purchased. All properly installed Waterguard+ systems are covered by our 5-year limited warranty.
Waterguard is not responsible for defects that do not affect the essential functioning of the product, or that are due to user error, accidents/accidents, overvoltage, use contrary to the supplier's or our instructions/product sheets, or lack of maintenance. The buyer's right to invoke defects also ceases if the product is altered or repaired by anyone other than the supplier without the prior written consent of the supplier. Waterguard is only liable under the warranty if the buyer complains within the warranty period and within the warranty period.
För detaljerte garantivilkår, se Waterguard produktgaranti (https://erp.felltech.no/document/share/42/f5f01eb5-9724-4507-a866-dfb2a972af30).
If components of your Waterguard+ system need to be repaired within the warranty period, please contact Waterguard Customer Support.
Extended warranty when registering Linkbox+ with Abra
By registering your Linkbox+ with Abra via the Abralife app, you as a customer get a 10-year extended warranty on the product. The warranty starts from the time of purchase or the time of takeover of the system if it is delivered in new builds.
To register Linkbox+; scan the QR code on the front of the Linkbox+ and follow the link. This will take you directly to the download and installation of the Abralife app, as well as the installation, registration and configuration of the Linkbox+ in your Abra smart home.
Comments
0 comments
Please sign in to leave a comment.